Chevrolet Silverado Tow Bar Wiring Installation And Review Videos
Hi there, Chevy owners Today in your 2012 Chevy Silverado, we're going to be taking a look at and showing you how to install Roadmaster's diode wiring kit. Now, when you flat tow to your vehicle, there are five main components that you're gonna need when doing so. You'll need your base plate, which is the connection point for your tow bar on your vehicle. You'll need your tow bar, which is the component that connects your vehicle to your motor home. Your safety cables, which is a supplemental connection in addition to your tow bar. You'll need your diode wiring, which takes all the lighting signals from your motor home and transfers to the lights at the back of your vehicle, so people know your intentions when going down the road and your supplemental breaking system, which will apply the brakes in your vehicle when you hit them in your motor home to help you come to a safe stop. more
Watch Video
4/13/2022 3:12:55 PM
Hopkins Custom Tail Light Wiring Kit Installation - 2008 Chevrolet Silverado- Video
Today on our 2008 Chevrolet Silverado we're going to be taking a look at and showing you how to install the Hopkins Custom Tail Light Wiring Kit for Towed Vehicles, part number HM56101. Here's what our wiring looks like fully installed. It's going to give us a four-pole flat bracket and wiring on the front of our vehicle. That way we can tow it and have all the required lights on the back end. Now, this is a custom kit. It's going to plug directly into your factory harness, so there's no cutting or splicing that you have to do. Now, it also has a convertor box to make sure that the lights on your motor home are going to match up with the ones on your vehicle. more
Watch Video
6/8/2017 10:57:08 AM
Tail Light Wiring Kit Installation - 2008 Chevrolet Silverado- Video
Today on our 2008 Chevy Silverado, we'll be installing the TrailerMate Custom Tail Light Wiring Kit for Towed Vehicles, part number TM780017. Note, we've already gone ahead and lowered and removed the spare tire to gain easier access to the rear tail-light wiring. Here at the back of the vehicle, at the vehicle's crossmember, near the driver's-side frame rail, will be electrical connection ports. We're looking for the blue wire connector. Once we locate it, we'll go ahead and press on the locking tab and remove it from the port. Then to get a little easier access to it, I'm going to go ahead and feed it up over the crossmember and then bring it down so that we can go ahead and remove the electrical tape that secures the wire loom in position. Now we'll go ahead and peel back the wire loom and locate the two brown wires, one yellow wire, and one dark green wire. Once we've located these wires, we can then go ahead and start connecting the new TrailerMate wiring harness. To begin, we'll go ahead and take one of the brown wires on the vehicle and cut it in half. more
Watch Video
6/9/2014 10:11:17 AM
Blue Ox Tail Light Wiring Kit Installation - 2010 Chevrolet Silverado- Video
Today, in our 2010 Chevy Silverado, well be installing the Blue Ox Tail Light Wiring Kit with bulb and socket, part number BX8869.To begin install, well start at the rear of the vehicle where well go ahead and lower the tailgate. This will give us access to the rear tail light fasteners. Theres two fasteners for each tail light. Well go ahead and remove the fasteners and then pop the tail light out of its position, being careful not to break the alignment tabs underneath.Next, well go ahead and find a suitable location for installing our socket. Here at the top of the tail light on the inside would be a good location. Using a 1 inch hole saw, well now go ahead and drill out the hole for the socket. more
Watch Video
11/5/2013 3:46:32 AM
Roadmaster Tow Bar Wiring Kit Installation - 2013 Chevrolet Silverado- Video
Today on this 2013 Chevrolet Silverado, we're going to install part number RM-154 Roadmaster. This is our diode wiring kit. Start off our install, we're going to remove one 4-pole or the long piece of wiring that has two 4-poles on the end. We're going to start working that wire from the front of the truck towards the back of the truck. We'll go ahead and run a wiring through the opening, by the base plate, we'll have to run it up and through the engine compartment. Once we've pull up our inaudible 00:00:30, we'll leave some out on the front of the truck where we'll install our loom material to help protect the wires by the bumper. more
Watch Video
8/12/2013 8:50:44 AM
1
Filter Videos
Filter Videos
